|
TABER® Industries offers a full line
of test accessories to be used with the TABER®
Rotary Platform Abraser (Abrader).
S-16; Steel Specimen Plates [part# 125563]
4" square, 20 gauge steel with ¼" hole (sold in packages of
10)
S-17; Wood Specimen Plaques [part# 132088-1]
4" square, ¼" birch plywood with ¼" hole (sold in packages
of 10)
S-18; Aluminum Specimen Plates [part# 132086]
4" square, Aluminum with ¼" hole (sold in packages of 10)
S-31; NEMA Glass Standardization Plates [part#
125561]
4" square, 1/8" plate glass with ¼" hole (sold in packages
of 10)
S-34; NEMA Zinc Standardization Plates [part# 125562]
4" square, 0.032" zinc with ¼" hole (sold in packages of 5)
S-38; Standardization Plates [part# 121257]
4" square, 1/16" plexiglass with ¼" hole (sold in packages
of 10)
S-32; NEMA Wheels [part# 125344]
Manufactured out of rubber, this wheel contains
no abrasive grain and is used to apply S-33 or
S-42 sandpaper strips (same as CS-0)
S-33; Sandpaper Strips [part# 121124]
Backed with a pressure sensitive adhesive, these
coated abrasive strips are attached to the
periphery of S-32 (CS-0) resilient rubber
wheels; 12.7mm x 160mm, 360 FEPA, closed coat
(sold in packages of 100 or 500)
S-42; Sandpaper Strips [part# 125564]
Backed with a pressure sensitive adhesive, these
coated abrasive strips are attached to the
periphery of S-32 (CS-0) resilient rubber
wheels; 12.7mm x 160mm, 180 ANSI-CAMI, open coat
(sold in packages of 100 or 500)
S-11; Refacing Discs [part# 121102]
4" diameter, 150 grit abrasive paper for
refacing resilient wheels (sold in packages of
100)
ST-11; Duplex Refacing Stone [part#
125777]
4" diameter x ¼" thick; Used to test natural or
synthetic rubber "wheels" molded or cut from
sheet, in place of a flat specimen. Also used to
reface CS-10F wheels. One side of stone contains
a coarse grit for refacing wheels at the start
of a test (new wheels reface 100 cycles,
previously used wheels reface 25 - 50 cycles);
the other side has a fine grit which is used at
intervals throughout a test (25 cycles each 1000
cycles for the duration of the test).
S-36; Specimen Mounting Cards [part#
125560]
4 ¼" square; Mounting card that has one side
coated with pressure sensitive adhesive to hold
textiles and other flexible test specimens
tightly to the mounting surface, preventing
wrinkles under the abrading wheels. On the plain
side of the card, a test record form is printed.
(sold in packages of 50)
S-36-1; Specimen Mounting Cards [part#
129270]
Same description as S-36, but round (sold in
packages of 50)
S-37; Specimen Mounting Sheets [part#
12558]
4 ¼" square; Both sides of smooth card stock are
coated with pressure sensitive adhesive,
overlaid with a protective paper that is peeled
off prior to use. Mounting sheets are
interleaved between the specimen and the abraser
turntable to provide a non-slip attachment for
material specimens such as ceramics, plastics
and glass - when no center hole is present.
(sold in packages of 100)
S-37; Specimen Mounting Sheets [part#
129271]
Same description as S-37, but round (sold in
packages of 100)
125g Counterweights [part# 126108]
Counterweight used with the Taber Abraser to reduce the
wheel load by 125 grams (2 pieces)
175g Counterweights [part# 133004]
Counterweight used with the Taber Abraser to reduce the
wheel load by 175 grams (2 pieces)
503-0022; Auxiliary Weight (500 gram load) [part#
125769]
Auxiliary weight used with the Taber Abraser to increase the
wheel load to 500 grams (requires 2 pieces). Note; actual
weight is 250 grams.
503-0023; Auxiliary Weight (1000 gram load) [part#
125770]
Auxiliary weight used with the Taber Abraser to increase the
wheel load to 1000 grams (requires 2 pieces). Note; actual
weight is 750 grams.
Replacement Auxiliary Weight Set [part# 125734]
Includes 500 gram load (503-0022) and 1000 gram load
(503-0023)
5130-70; Replacement Vacuum Set (120V, 60Hz) [part#
121127]
The Abraser Vacuum Unit is manufactured specifically for use
with the TABER Abraser, and incorporates a heavy-duty motor
with life-lubricated sealed bearings. Mounted above a sturdy
tank, the motor is kept clear of dust and debris resulting
from your testing.
A flexible suction hose is provided to connect the vacuum
unit with the abraser or other accessory instrument. And a
round clean-up brush aids in cleaning loose debris from the
instrument or surrounding work area, includes flexible
suction hose and round brush
5131-70; Replacement Vacuum Set (230V, 50Hz) [part#
127788]
Same description as 5130-70
Replacement Paper Filter Bag [part# 114309]
For use with Taber Vacuum equipped with plastic tanks
Replacement Paper Filter Bag [part# 129259]
For use with Taber Vacuum equipped with metal tanks
Cloth Filter Bag [part# 128086]
For use with Taber Vacuum
Filter, Cartridge Type [part# 131680]
For use with Taber Vacuum
Replacement Foam Filter [part# 114310]
For use with Taber Vacuum
Replacement Round Brush [part# 114312]
For use with Taber Vacuum
Replacement Flexible Suction Hose [part# 114311]
For use with Taber Vacuum
Taber Abraser Clean-up Hose [part#
129280]
Using the vacuum only feature on your abraser,
this simple accessory makes clean-up easy. The
hose mounts to the rear vacuum nozzle opening.
The small brush is ideal for cleaning test
specimens, the abraser or your work area without
the need to disconnect the vacuum hose from your
abraser.
S-21; Extension Nut [part# 121224]
Provides the ability to test materials ¼" - ½"
thick (samples require 3/8" diameter center
hole)
S-19; Rubber Pad [part# 121016]
4 ¼" O.D. pad for Specimen Holder (sold in
packages of 5)
S-12; Brush [part# 121103]
Brush for cleaning Specimen Plates
100-237; Wrench [part# 121095]
For use with hold down ring clamp screw
ETF-11; Step-down Transformer [part#
121110]
230/115V, 50/60Hz, 1000 watt
Top
|
