-
Earing Test Machine ISO, DIN EN
-
Bead Test Instrument
-
Cupping &
Deep-drawing Cup Test Machine ISO, BS, DIN,
NF, SIS
-
Cupping &
Deep-drawing Cup Test Machine ISO, ASTM, BS,
DIN, EN, DIN, NF, SIS
-
Flow Time
Measuring Instrument ISO, ASTM, DIN
-
Visco
Test Blade acc. to Rossmann
-
Viscosoft
460 FC Software DIN, EN ISO, ASTM
-
Density
Ball ISO, DIN, VDA
-
Paint
Resistance Measuring Instrument
-
Contrast
Chart ISO, ASTM, BS, DIN
-
Duplex
or Triplex Film Applicator acc. to Biddle
-
Film
Applicator System Wasag
-
Centrifugal Film Applicator
-
Film
Applicator ASTM
-
Film
Applicator
-
Autospray - Test Panel Spraying Applicator
Type APL 1.1
-
Coatmaster 509 MC Film Applicator
-
Drying
Time Tester EN ISO, DIN
-
Coatmaster 509 MC III - Film Applicator &
Drying Time Recorder
-
Wet &
Dry Film Thickness Gayge acc. to Rossmann
ISO, EN ISO, ASTM. BS, FTMS
-
TNO
Paint Borer 518 S - Thickness Gauge ISO, EN
ISO, ASTM, DIN
-
PenTest
- Thickness Gauge ISO, ASTM, BS, DIN
-
MikroTest 5,6 & 7-Thickness Gauge ISO, ASTM,
BS, DIN
-
GalvanoTest - Thickness Gauge ISO, ASTM, BS,
DIN
-
Scratch
Hardness Tester 430 P- ISO,EN ISO, DIn,
ASTM, ECCA, JIS, SIS,SNV,GME,VDA
-
Scratch
Test Station acc. to BMW/ERICHSEN, Model 450
-
Impact
Tester acc. to Wegner ISO, DIN ISO, DIN EN,
EN, DIN
-
SPLITT
II 408-Single Blow Impact Tester DIN
-
Bend &
Impact Tester
-
Stone
Hammer Blow Testing Instrument acc. to VDA,
Peugeot-Citroen, Renault, DIN
-
Scratch
Hardness Tester acc. to Clemen ISO, EN ISO
-
Pendulum
Damping Tester ISO, EN ISO, ASTM, BS, DIN,
NEN, NF, SIS, SNV, VDA
-
Universal Scratch Tester 413 ISO, DIN, EN
-
Washability & Scrub Resistance Tester ISO,
DIN EN ISO, ASTM, DIN, SIS
-
Chalking
Rate Tester acc. to Kempf DIN
-
Picogloss 500 MC-Gloss Meter ISO, EN ISO,
ASTM, BS, DIN, NF, JIS, SIS
-
Picogloss 503-Gloss Meter ISO, EN ISO, ASTM,
BS, DIN, NF, JIS, SIS
-
Glossmaster Online 507
-
Tint
Tester 527-Brightness Measuring Instrument
ISO, ASTM, BS, DIN
-
Scratchmarker 427-Coat Throughscratching
Instrument
-
Solventchecker 434-Corrosion Test Instrument
-
Scratch
Stylus acc. to sikkens
-
Solarbox
522-Light Exposure Test Appa. ISO, ASTM,
DIN, UNI
-
Hygrotherm 529-Humidity Cabinet ISO, ASTM,
BS, DIN, NF, VDA, ECCA
-
Corrocutter 639-Coat Throughscratching
Instrument
-
Unimat
056-Tensile & Pressure Testing Machine DIN
EN ISO
-
Physimeter 906 MC-Multi Measuring Device
-
Scratch Hardness
Tester LINEAR TESTER 249
|
Earing Test Machine ISO, DIN EN

Intended for series tests of stamping lacquers and similar
coatings on sheet metal up to 1.2 mm thick by blanking and
drawinga cylindrical standard cup in one operation. Blanking
and drawing force 80 kN, electro-hydraulic drive. Due to its
special construction it is particularly recommendable for
Deep Drawing Cup Test on foils.
Top

Bead Test Instrument

For numerical evaluation of the quality of stamping lacquers
and plastic coatings on cylindrical standard cups.
Top

Cupping & Deep-drawing Cup Test Machine ISO, BS, DIN, NF,
SIS

Especially intended for coil coatings, this machine is
suitable for the ERICHSEN Cupping Test as well as for the
Deep Drawing Cup Test producing cylindrical and square cups.
To intensify the material stressing it is possible to
conduct a first and second re-drawing operation. Blanking,
drawing and ejection of the cup is carried out in one
operation. The sheet thickness to be tested depends on the
quality of the material and on the required test method.
Blanking force: 200 kN
Drawing force: 200 kN
Top

Cupping & Deep-drawing Cup Test Machine ISO, ASTM, BS, DIN,
EN, DIN, NF, SIS

Intended for the ERICHSEN Cupping Test and for the Deep
Drawing Cup Test. Electro-hydraulic drive, variable drawing
speed as well as a blanking press integrated into the test
head allow the manufacturing of a cup (blanking, drawing and
ejection) in one operation. The sheet thickness to be tested
depends on the quality of the material and on the required
test method.
Blanking force: 200 kN
Drawing force: 100 kN
Top

Flow Time Measuring Instrument ISO, ASTM, DIN

Objective determination of flow time for viscosity
measurements using standardized flow cups. Including
temperature bath and adapter rings for the diff-ferent flow
cups. Automatic measuring sequence with optical detection of
the efflux stream of sample. Flow times up to 200 s can be
read from the LCD with an accuracy of 0.01s.
Top

Visco Test Blade acc. to Rossmann

A
simple reliable instrument for checking the required
brushing or spraying consistency of coating materials.
Invaluable for users of paint. Serves also as stirrer for
thinn-ning down small quantities.
Top

Viscosoft 460 FC Software DIN, EN ISO, ASTM

Software for rapid conversion between viscosity and efflux
time, for use with standardised flow cups. Converts between
dynamic and kinematic viscosity. Clearly arranged graphics,
easy to use.
Top

Density Ball ISO, DIN, VDA

For rapid determination of density of liquids. A sphere of
volume 100 or 10 ml is immersed in a beaker the contents of
which have been previously weighed. The increase in liquid
level given in grams (g) corresponds with 100 or 10 x the
value of the density. The equipment is easily cleaned after
use.
Top

Paint Resistance Measuring Instrument

To
measure electrical resistance of paints in the range from
0-20 MD. Specially suited to establish characteristics of
dipping paints and monitoring spray paints for electrostatic
processes. Portable measuring system. Display of measuring
value after defined measuring time. Easy to clean dip-in
measuring probe with annular gap.
Top

Contrast Chart ISO, ASTM, BS, DIN

24
test card versions available, in different sizes, patterns
and colourings, including special penetration cards for
watery systems.
Top

Duplex or Triplex Film Applicator acc. to Biddle

To
produce 2 or 3 parallel paint films on test cards under
identical and reproducible application conditions. Paint
specimens produced for visual comparison or to build up a
colour tone collection. Standard film thicknesses
100/150/200/250 µm.
Top

Film Applicator System Wasag

Duplex film applicator for film widths 80/120/180/230 mm.
Made of corrosion resistant steel. The two gaps can be
chosen as desired from the range 15-2000 µm.
Top

Centrifugal Film Applicator

To
produce specimen panels with an evenly applied paint film of
defined thickness. Variable speed from 100-2500 min-1.
Top

Film Applicator ASTM

Motor-driven film applicator for the application of coatings
of an even and defined thickness onto glass plates, contrast
charts, foils, etc.. Equipped with a multi-functional
applicator support appropriate for most of the normally used
applicators (spiral film applicators, gap applicators of
various dimensions). Adjustable speed up to 99 mm/s. Maximum
application area approx. 330 mm x 345 mm.To be used
optionally with glass plate, vacuum suction plate or
flexible application substrates.
Top

Film Applicator

A
film applicator with variable gap height. Clearance
adjustable in the range 0-1000 µm by means of a micrometer
screw (accuracy 1 µm). Available for film widths 80/150/ 220
mm.
Top

Autospray - Test Panel Spraying Applicator Type APL 1.1

This modern and inexpensive spray applicator for test panels
has been designed for reproducible application of coating
substances onto various substrates. It is easy to operate
and can also be used in hazardous areas. The control unit of
the AUTOSPRAY allows not only the use of fixed programmed
spraying parameters such as step sizes, horizontal stroke
speeds, number of spraying strokes and ventilation time, but
also permits to adapt to practically all conceivable
requirements of coating technology by altering the settings.
The AUTO-SPRAY 481 is pre-fitted to enable the use of one or
two automatic flow cup spray guns. Optionally a material
conveyor unit as well as a "cross-path" programme can be
supplied.
Top

Coatmaster 509 MC Film Applicator

Intended for the application of even paint films of defined
thickness on glass panes, test charts or foils. Control box
on flexible lead with foil keyboard and LCD to control the
working movement, to determine the operation mode and to
select the working parameters.
The version 509 MC III is a combined Film Applicator and
Drying Time Recorder.
Top

Drying Time Tester EN ISO, DIN

A
simple plunger type press for meas-uringdegree of dryness in
accordance with DIN 53 150 in the range from 2 to 7. A glass
tube Ballotini dispenser to measure degree of dryness 1 is
available as accessory.
Top

Coatmaster 509 MC III - Film Applicator & Drying Time
Recorder

Besides its function as a film applicator, this combined
instrument also offers the possibility to evaluate the
degree of dryness of 7 identical or different paint
specimens simultaneously. Most versatile instrument due to a
variety of accessories. Mobile control box with LCD to
select the working movement, the operation mode as well as
the working parameters.
Top

Wet & Dry Film Thickness Gayge acc. to Rossmann ISO, EN ISO,
ASTM. BS, FTMS

For measurements on wet films the contact point is raised by
means of a knurled screw and then lowered until it touches
the surface of the wet film.
Top

TNO Paint Borer 518 S - Thickness Gauge ISO, EN ISO, ASTM,
DIN

For film thickness measurements using the wedge cut
technique. Combines the advantages of P.I.G. 455 with
greater ease of operation: a conical bore of defined angle
is made in the coating. Measuring microscope, easily and
accurately focused over the cut out. Minimum specimen damage
allows a large number of test points.
Specimen table for extremely small specimens (dia. 10 mm)
available as accessory. Due to the mobility of the
microscope into two directional axes (turned by 90° from one
another) with the possibility of turning the scale, the
PAINT BORER 518 S is especially suitable for the evaluation
of elliptical holes that arise with curved specimens.
Top

PenTest - Thickness Gauge ISO, ASTM, BS, DIN

Inexpensive instrument using the magnetic pull-off method
for rapid non-destructive measurement of non-magnetic layers
on steel. Measuring result held mechanically. No electrical
supply required.
Measuring range: 25-700 µm
Top

MikroTest 5,6 & 7-Thickness Gauge ISO, ASTM, BS, DIN

For non-magnetic coatings on steel using the non-destructive
magnetic pull-off technique. No electrical current required.
Measuring result held mechanically. With unique automatic
measuring system for reproducible results, even under
extreme measuring conditions.
Mikrotest 5 and 6: 9 analog versions for a total measuring
range 1 µm - 20 mm, also for electro-plated nickel layers on
various base materials.
Mikrotest 7:
4 digital versions for a total measuring range 0.5 µm to 15
mm.
Top

GalvanoTest - Thickness Gauge ISO, ASTM, BS, DIN

To
measure metallic single or multi layer coatings on a
metallic base by electrochemical removal. Particularly
suitable for galvanic coatings. Total measuring range:
0.3-40 µm.
Special electrolytes for more than 70 combinations of
coating and base material. Minimum measuring area: 0.25 mm2.
Interface RS 232 C for printer or PC.
Top

Scratch Hardness Tester 430 P- ISO,EN ISO, DIn, ASTM, ECCA,
JIS, SIS,SNV,GME,VDA

Versatile instrument for mechanical tests: cross hatch cut,
scratch (mar) resistance, scratch hardness and writing
effect. Manual setting of the loadingforce (max. 50 N)
(Model 430 P I) or motor-driven adjustment (Model 430 P II).
9 preset cross-cuts in compliance with the most commmonly
used standards; in addition one freely programmable
cross-cut pattern. Two cutting speeds and two cutting
lengths can be combined as required. Rapid clamping device
for test panels and visual display upon cutting through
insulating layers to metal subtrate.
Top

Impact Tester acc. to Wegner ISO, DIN ISO, DIN EN, EN, DIN

Portable and handy instrument especially designed for tests
on enamel in accordance with DIN EN ISO 4532. Enables the
user to carry out tests on site.
Optional accessory: Special support for testing plastic
surfaces.
Top

SPLITT II 408-Single Blow Impact Tester DIN

Testing instrument designed as bench-top unit, for
single-blows using steel balls (dia. 2 mm). SPLITT II 408 is
equipped with two testing temperatures (+23°C or -20°C),
SPLITT III 408 is equipped with three testingtempera-tures
(+23°C , 0 °C and -20°C), internally controlled and
displayed on LCD. Variable speed of the bombardment preset
to 250 km/h for tests in accordance with the standard, also
displayed on LCD. The angle of impact shows a deviation of
2° to the vertical. To prevent icing of the specimen the
test room can be swept with nitrogen. A scale at the
specimen aperture facilitates the positioning of the
bombardment. This test method is already prescribed in the
works specifications of a renowned vehicle manufacturer.
Top

Bend & Impact Tester

The performance of a coated sheet metal panel, previously
formed to a U-shape when it is deformed by conical bar in a
sudden blow can be examined.
Top

Stone Hammer Blow Testing Instrument acc. to VDA,
Peugeot-Citroen, Renault, DIN

A
multi-blow test instrument developed in association with the
automotive industry, offering outstanding reproducibility
and comparability of results. The pressure accumulator
dampens variations in the compressed air mains. Supply of
shot particles adjustable.
Top

Scratch Hardness Tester acc. to Clemen ISO, EN ISO

Scratching caused by moving the specimen under a
knife-shaped or spherical test tip made of tungsten carbide,
with a defined load (0-20 N). The scratch hardness
corresponds to the force that is necessary to scratch
through the surface coating. Electrically driven with
constant scratching speed.
Top

Pendulum Damping Tester ISO, EN ISO, ASTM, BS, DIN, NEN, NF,
SIS, SNV, VDA

Damping of the oscillations of a pendulum resting on the
coating material in accordance with the standards. Two
pendulum versions with automatic adjustment: in accordance
with Koenig and Persoz. In addition, two different measuring
modules: basic version with manual pendulum excursion and
automatic version. Measuring values are shown on the digital
display of the control terminal.
Top

Universal Scratch Tester 413 ISO, DIN, EN

Compact turntable instrument used to determine the scratch
hardness and the resistance to scratching of lacquer, glass
or plastic surfaces (specifically HPDL coatings). Four
different, exchangeable test tools equipped with Tungsten
carbide or diamond tips with defined test geometries. Two
weights sliding on a scale beam, for load ranges of 0.01 to
1 N and 0.1 to 10 N.
Top

Washability & Scrub Resistance Tester ISO, DIN EN ISO, ASTM,
DIN, SIS

Robust instrument for standard coating materials. Available
access-tests of washability and scrubbabili- sories:
standard brushes, PVC foils ty of emulsion paints and
similar (Leneta® equivalent), dosing pump.
Top

Chalking Rate Tester acc. to Kempf DIN

Damp photographic paper is pressed by a rubber pad under
defined force onto the film surface in accordance with DIN
53 159. Evaluation of chalking mark by comparison with
sample scale.
Top

Picogloss 500 MC-Gloss Meter ISO, EN ISO, ASTM, BS, DIN, NF,
JIS, SIS

Two angle, portable gloss meter for standardised measuring
geometries of 20°/60°. Autoranging faciliy to mirror gloss
measurements. Microcontroller electronics for automatic
calibration and measuring data memory (up to 500 values
divided into max. 99 batches), LCD for display of measuring
results, status message and memory management.
Bi-directional interface for external control via PC and
Windows based software PICOSOFT (option).
Top

Picogloss 503-Gloss Meter ISO, EN ISO, ASTM, BS, DIN, NF,
JIS, SIS

Compact, battery operated gloss meter with three measuring
geometries: 20°, 60° and 85°. Autoranging faciliy to mirror
gloss measurements. Data storage, statistical functions and
interface, transmission cable to PC and software for data
transmission and storing (enables statistical evaluation of
data). Carrying case included.
Top

Glossmaster Online 507

Consisting of measuring head and supply and display unit for
non-contact gloss measurement on the process line. 10 mm
measuring distance. Built-in calibration standard and dust
protected versions on request. An electrically controlled
traversing device carrying the measuring head can also be
supplied.
Top

Tint Tester 527-Brightness Measuring Instrument ISO, ASTM,
BS, DIN

Special laboratory version for dark paste type test layers,
with 41/2 digit LED display and special measuring head. In
addition to tinting strength measurement in accordance with
ASTM D 3265/2745 also for standard brightness measurements.
Can be equipped with BCD/RS 232/analogue output.
Top

Scratchmarker 427-Coat Throughscratching Instrument

Portable instrument to apply defined scratches through
coatings on specimen panels used for corrosion tests.
Compact construction for fatigue-free operation. Scratch
tool with van Laar geometry. Defined adjustment of the depth
of the scratch in increments of 25 µm.
Top

Solventchecker 434-Corrosion Test Instrument

Simple and practical instrument for testing paints and
plastics for their resistance to chemicals under static
conditions giving results simultaneously for the effects of
liquids and vapours as well as in the threshold area. 4
tests can be performed in parallel.
Top

Scratch Stylus acc. to sikkens

This hand operated instrument complete with carbide cutting
tip provides a convenient means of scoring a 1 mm (optional
0.3, 0.5 mm or 2 mm) wide rectangular track in a surface
coating - for corrosion tests.
Top

Solarbox 522-Light Exposure Test Appa. ISO, ASTM, DIN, UNI

Compact instrument to determine the resistance to exposure
to sun light using a Xenon high pressure lamp (1.5 kW or 2.5
kW). Adjustable level of irradiance, uniform illumination by
special mirror system, exchangeable filters for variable UV
fraction. Four versions available:
- SOLARBOX 522/1500, 522/3000
- SOLARBOX 522/1500e, 522/3000e (each without and with
microprocessor controls)
Light Exposure Test Apparatus
- SOLARBOX 522/1500e RH
- SOLARBOX 522/3000e RH
are extended versions of Model 522/1500e and 522/3000e with
additional control/monitoring of relative humidity in the
test chamber during the test.
Optional: Programmable flooding system for periodic wetting
of specimens.
Top

Hygrotherm 529-Humidity Cabinet ISO, ASTM, BS, DIN, NF, VDA,
ECCA

Inexpensive apparatus for testing the corrosion resistance
of specimens in condensation water climate with or without
S02 addition in accordance with different
standards. Robust 300 I plastic chamber with front door
loading.
Top

Corrocutter 639-Coat Throughscratching Instrument

Comfortable, manual instrument for fatigue-free application
of defined scratches on coated specimen panels intended for
corrosion tests. Provided for use of scratching tools in
accordance with Clemen, van Laar and Sikkens frequently used
in practice. Avoids the great strain usually put to fingers
and wrists when scratching specimen in large series. Using
adequate scratch templates available as accessories, it is
possible to apply 90° cross scratches as well as 60°/120°
St. Andrew's cross scratches.
Top

Unimat 056-Tensile & Pressure Testing Machine DIN EN ISO

Universal testing machine, maximum testing force 200 kN,
equipped with a control and evaluation unit UNICONTROL. The
control is carried out by two integrated standard PCs: The
first industrial PC performs the real time critical control
and the measuring data acquisition, the second PC presents a
user friendly visualisation and run-off control. The
accuracy of 0.1 % and the measuring data recording of
several thousands words per second exceed even the extremely
high demands of the corresponding standard DIN EN ISO 7500/1
for testing machines.
Top

Physimeter 906 MC-Multi Measuring Device

Designed as a mobile system the PHYSIMETER® 906 MC-E is
equipped with four channels for simultaneous data-recording
of physical values such as force, stroke, pressure as well
as the number of revolutions, torque or rotational angles.
The versatile amplifier allows the connection of strain
gauges, inductive stroke sensors, digital and analogue
signals.The connected sensors are automatically identified
and can be changed during operation. The strong aluminium
housing plus optional force sensor enables the unit to be
integrated in a stationary measuring system and is
suitablefora load of 1 kN.Values and graphics are shown on a
illuminated graphic display which can be turned 180°
permitting data to be read in any testing situation.
Top

Scratch Test Station acc. to BMW/ERICHSEN, Model 450

PLC controlled test system comprising a basic unit and a
control unit, with a motor-driven X-Y- specimen table, a
universal holding fixture with vertical linear guide and
pneumatic tool feed motion as well as a touch-screen control
panel.
The scope of supply includes: mains cable CEE 16A, air hose,
clamping claws, tool adapter for test tips, test tip acc. to
ISO (Ř 1 mm), 7 load weights, fork wrenches SW10 and SW19 as
well as allan keys SW3 and SW5.
Power supply: 400 VAC, 50/60 Hz, TN or TT net
Net weight/basic unit: approx. 115 kg
Net weight/control unit: approx. 40 kg
Top
For more details on
Erichsen products please visit
www.erichsen.de
|